Repetier FW 設定檔 for ATOM (Mega2560)

編輯歷史

時間	作者	版本
2017-07-24 13:10 – 13:16	(unknown)	r0 – r3
顯示 diff + Repetier FW 設定檔 for ATOM (Mega2560) + + 把自己嘗試出來的Repetier FW 設定檔貼上來這邊,方便討論跟整合出較適合的設定for ATOM + 也一方面大家幫忙一起理解設定各參數的意義 + + Step by Step from Marlin to Repetier FW + + /* + This file is part of Repetier-Firmware. + + Repetier-Firmware is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 3 of the License, or + (at your option) any later version. + + Repetier-Firmware is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with Repetier-Firmware. If not, see <http://www.gnu.org/licenses/>. + + / + + #ifndef CONFIGURATION_H + #define CONFIGURATION_H + + /************* READ FIRST ********************** + + This configuration file was created with the configuration tool. For that + reason, it does not contain the same informations as the original Configuration.h file. + It misses the comments and unused parts. Open this file file in the config tool + to see and change the data. You can also upload it to newer/older versions. The system + will silently add new options, so compilation continues to work. + + This file is optimized for version 0.91 + generator: http://www.repetier.com/firmware/v091/ + + If you are in doubt which named functions use which pins on your board, please check the + pins.h for the used name->pin assignments and your board documentation to verify it is + as you expect. + + / + + #define NUM_EXTRUDER 1 + #define MOTHERBOARD 33 + + #include "pins.h" + + // ################## EDIT THESE SETTINGS MANUALLY ################ + // ################ END MANUAL SETTINGS ########################## + + #define FAN_BOARD_PIN -1 + #define X_MIN_PIN -1 + #define Y_MIN_PIN -1 + + //#define EXTERNALSERIAL use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer. + // Uncomment the following line if you are using arduino compatible firmware made for Arduino version earlier then 1.0 + // If it is incompatible you will get compiler errors about write functions not beeing compatible! + //#define COMPAT_PRE1 + #define MIXING_EXTRUDER 0 + + #define DRIVE_SYSTEM 3 + #define XAXIS_STEPS_PER_MM 80 + #define YAXIS_STEPS_PER_MM 80 + #define ZAXIS_STEPS_PER_MM 80 + #define EXTRUDER_FAN_COOL_TEMP 50 + #define PDM_FOR_EXTRUDER 1 + #define PDM_FOR_COOLER 1 + #define DECOUPLING_TEST_MAX_HOLD_VARIANCE 20 + #define DECOUPLING_TEST_MIN_TEMP_RISE 1 + #define RETRACT_ON_PAUSE 2 + #define PAUSE_START_COMMANDS "" + #define PAUSE_END_COMMANDS "" + #define EXT0_X_OFFSET 0 + #define EXT0_Y_OFFSET 0 + #define EXT0_STEPS_PER_MM 100 + #define EXT0_TEMPSENSOR_TYPE 8 + #define EXT0_TEMPSENSOR_PIN TEMP_0_PIN + #define EXT0_HEATER_PIN HEATER_0_PIN + #define EXT0_STEP_PIN ORIG_E0_STEP_PIN + #define EXT0_DIR_PIN ORIG_E0_DIR_PIN + #define EXT0_INVERSE 0 + #define EXT0_ENABLE_PIN E0_ENABLE_PIN + #define EXT0_ENABLE_ON 0 + #define EXT0_MAX_FEEDRATE 300 + #define EXT0_MAX_START_FEEDRATE 20 + #define EXT0_MAX_ACCELERATION 3000 + #define EXT0_HEAT_MANAGER 1 + #define EXT0_WATCHPERIOD 1 + #define EXT0_PID_INTEGRAL_DRIVE_MAX 210 + #define EXT0_PID_INTEGRAL_DRIVE_MIN 40 + #define EXT0_PID_PGAIN_OR_DEAD_TIME 20.74 + #define EXT0_PID_I 3.19 + #define EXT0_PID_D 33.68 + #define EXT0_PID_MAX 210 + #define EXT0_ADVANCE_K 0 + #define EXT0_ADVANCE_L 0 + #define EXT0_ADVANCE_BACKLASH_STEPS 0 + #define EXT0_WAIT_RETRACT_TEMP 150 + #define EXT0_WAIT_RETRACT_UNITS 0 + #define EXT0_SELECT_COMMANDS "" + #define EXT0_DESELECT_COMMANDS "" + #define EXT0_EXTRUDER_COOLER_PIN -1 + #define EXT0_EXTRUDER_COOLER_SPEED 255 + #define EXT0_DECOUPLE_TEST_PERIOD 12000 + #define RETRACT_DURING_HEATUP true + #define PID_CONTROL_RANGE 20 + #define SKIP_M109_IF_WITHIN 2 + #define SCALE_PID_TO_MAX 0 + #define TEMP_HYSTERESIS 0 + #define EXTRUDE_MAXLENGTH 160 + #define NUM_TEMPS_USERTHERMISTOR0 0 + #define USER_THERMISTORTABLE0 {} + #define NUM_TEMPS_USERTHERMISTOR1 0 + #define USER_THERMISTORTABLE1 {} + #define NUM_TEMPS_USERTHERMISTOR2 0 + #define USER_THERMISTORTABLE2 {} + #define GENERIC_THERM_VREF 5 + #define GENERIC_THERM_NUM_ENTRIES 33 + #define HEATER_PWM_SPEED 0 + + // ############# Heated bed configuration ######################## + + #define HAVE_HEATED_BED 0 + #define HEATED_BED_MAX_TEMP 120 + #define SKIP_M190_IF_WITHIN 3 + #define HEATED_BED_SENSOR_TYPE 1 + #define HEATED_BED_SENSOR_PIN TEMP_1_PIN + #define HEATED_BED_HEATER_PIN HEATER_1_PIN + #define HEATED_BED_SET_INTERVAL 5000 + #define HEATED_BED_HEAT_MANAGER 0 + #define HEATED_BED_PID_INTEGRAL_DRIVE_MAX 255 + #define HEATED_BED_PID_INTEGRAL_DRIVE_MIN 80 + #define HEATED_BED_PID_PGAIN_OR_DEAD_TIME 196 + #define HEATED_BED_PID_IGAIN 33 + #define HEATED_BED_PID_DGAIN 290 + #define HEATED_BED_PID_MAX 255 + #define HEATED_BED_DECOUPLE_TEST_PERIOD 300000 + #define MIN_EXTRUDER_TEMP 150 + #define MAXTEMP 275 + #define MIN_DEFECT_TEMPERATURE -10 + #define MAX_DEFECT_TEMPERATURE 290 + + // ################ Endstop configuration ##################### + + #define ENDSTOP_PULLUP_X_MIN true + #define ENDSTOP_X_MIN_INVERTING false + #define MIN_HARDWARE_ENDSTOP_X false + #define ENDSTOP_PULLUP_Y_MIN true + #define ENDSTOP_Y_MIN_INVERTING false + #define MIN_HARDWARE_ENDSTOP_Y false + #define ENDSTOP_PULLUP_Z_MIN true + #define ENDSTOP_Z_MIN_INVERTING true + #define MIN_HARDWARE_ENDSTOP_Z true + #define ENDSTOP_PULLUP_X_MAX true + #define ENDSTOP_X_MAX_INVERTING false + #define MAX_HARDWARE_ENDSTOP_X true + #define ENDSTOP_PULLUP_Y_MAX true + #define ENDSTOP_Y_MAX_INVERTING false + #define MAX_HARDWARE_ENDSTOP_Y true + #define ENDSTOP_PULLUP_Z_MAX true + #define ENDSTOP_Z_MAX_INVERTING false + #define MAX_HARDWARE_ENDSTOP_Z true + #define max_software_endstop_r true + + #define min_software_endstop_x true + #define min_software_endstop_y true + #define min_software_endstop_z false + #define max_software_endstop_x false + #define max_software_endstop_y false + #define max_software_endstop_z false + #define ENDSTOP_X_BACK_MOVE 1 + #define ENDSTOP_Y_BACK_MOVE 1 + #define ENDSTOP_Z_BACK_MOVE 1 + #define ENDSTOP_X_RETEST_REDUCTION_FACTOR 5 + #define ENDSTOP_Y_RETEST_REDUCTION_FACTOR 5 + #define ENDSTOP_Z_RETEST_REDUCTION_FACTOR 5 + #define ENDSTOP_X_BACK_ON_HOME 0 + #define ENDSTOP_Y_BACK_ON_HOME 0 + #define ENDSTOP_Z_BACK_ON_HOME 0 + #define ALWAYS_CHECK_ENDSTOPS 0 + + // ################# XYZ movements ################### + + #define X_ENABLE_ON 0 + #define Y_ENABLE_ON 0 + #define Z_ENABLE_ON 0 + #define DISABLE_X 0 + #define DISABLE_Y 0 + #define DISABLE_Z 0 + #define DISABLE_E 0 + #define INVERT_X_DIR 1 + #define INVERT_Y_DIR 1 + #define INVERT_Z_DIR 1 + #define X_HOME_DIR -1 + #define Y_HOME_DIR -1 + #define Z_HOME_DIR 1 + #define X_MAX_LENGTH 200 + #define Y_MAX_LENGTH 200 + #define Z_MAX_LENGTH 350 + #define X_MIN_POS 0 + #define Y_MIN_POS 0 + #define Z_MIN_POS 0 + + // ########################################################################################## + // ## Movement settings ## + // ########################################################################################## + + #define FEATURE_BABYSTEPPING 1 + #define BABYSTEP_MULTIPLICATOR 1 + + #define DELTA_SEGMENTS_PER_SECOND_PRINT 180 // Move accurate setting for print moves + #define DELTA_SEGMENTS_PER_SECOND_MOVE 70 // Less accurate setting for other moves + + // Delta settings + #define DELTA_DIAGONAL_ROD 228.82 // mm + #define DELTA_ALPHA_A 210 + #define DELTA_ALPHA_B 330 + #define DELTA_ALPHA_C 90 + #define DELTA_RADIUS_CORRECTION_A 0 + #define DELTA_RADIUS_CORRECTION_B 0 + #define DELTA_RADIUS_CORRECTION_C 0 + #define DELTA_DIAGONAL_CORRECTION_A 0 + #define DELTA_DIAGONAL_CORRECTION_B 0 + #define DELTA_DIAGONAL_CORRECTION_C 0 + #define END_EFFECTOR_HORIZONTAL_OFFSET 0 + #define CARRIAGE_HORIZONTAL_OFFSET 0 + #define DELTA_MAX_RADIUS 105 + #define ROD_RADIUS 105.31 + #define PRINTER_RADIUS 105.31 + #define DELTA_HOME_ON_POWER 0 + #define STEP_COUNTER + #define DELTA_X_ENDSTOP_OFFSET_STEPS 0 + #define DELTA_Y_ENDSTOP_OFFSET_STEPS 0 + #define DELTA_Z_ENDSTOP_OFFSET_STEPS 0 + #define DELTA_FLOOR_SAFETY_MARGIN_MM 15 + //#define SOFTWARE_LEVELING + + #define DELTASEGMENTS_PER_PRINTLINE 24 + #define STEPPER_INACTIVE_TIME 360L + #define MAX_INACTIVE_TIME 0L + #define MAX_FEEDRATE_X 300 + #define MAX_FEEDRATE_Y 300 + #define MAX_FEEDRATE_Z 300 + #define HOMING_FEEDRATE_X 80 + #define HOMING_FEEDRATE_Y 80 + #define HOMING_FEEDRATE_Z 80 + #define HOMING_ORDER HOME_ORDER_ZXY + #define ENABLE_BACKLASH_COMPENSATION 0 + #define X_BACKLASH 0 + #define Y_BACKLASH 0 + #define Z_BACKLASH 0 + #define RAMP_ACCELERATION 1 + #define STEPPER_HIGH_DELAY 0 + #define DIRECTION_DELAY 0 + #define STEP_DOUBLER_FREQUENCY 12000 + #define ALLOW_QUADSTEPPING 1 + #define DOUBLE_STEP_DELAY 1 // time in microseconds + #define MAX_HALFSTEP_INTERVAL 1999 + #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 3000 + #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 3000 + #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 3000 + #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 4500 + #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 4500 + #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 4500 + #define MAX_JERK 20 + #define MAX_ZJERK 20 + #define PRINTLINE_CACHE_SIZE 16 + #define MOVE_CACHE_LOW 10 + #define LOW_TICKS_PER_MOVE 250000 + #define FEATURE_TWO_XSTEPPER 0 + #define X2_STEP_PIN ORIG_E1_STEP_PIN + #define X2_DIR_PIN ORIG_E1_DIR_PIN + #define X2_ENABLE_PIN ORIG_E1_ENABLE_PIN + #define FEATURE_TWO_YSTEPPER 0 + #define Y2_STEP_PIN ORIG_E1_STEP_PIN + #define Y2_DIR_PIN ORIG_E1_DIR_PIN + #define Y2_ENABLE_PIN ORIG_E1_ENABLE_PIN + #define FEATURE_TWO_ZSTEPPER 0 + #define Z2_STEP_PIN ORIG_E1_STEP_PIN + #define Z2_DIR_PIN ORIG_E1_DIR_PIN + #define Z2_ENABLE_PIN ORIG_E1_ENABLE_PIN + #define FEATURE_DITTO_PRINTING 0 + #define USE_ADVANCE 0 + #define ENABLE_QUADRATIC_ADVANCE 0 + + + // ################# Misc. settings ################## + + #define BAUDRATE 250000 + #define ENABLE_POWER_ON_STARTUP 1 + #define POWER_INVERTING 0 + #define KILL_METHOD 1 + #define GCODE_BUFFER_SIZE 2 + #define ACK_WITH_LINENUMBER 1 + #define WAITING_IDENTIFIER "wait" + #define ECHO_ON_EXECUTE 1 + #define EEPROM_MODE 1 + #define PS_ON_PIN ORIG_PS_ON_PIN + + / ======== Servos ======= + Control the servos with + M340 P<servoId> S<pulseInUS> / ServoID = 0..3 pulseInUs = 500..2500 + Servos are controlled by a pulse width normally between 500 and 2500 with 1500ms in center position. 0 turns servo off. + WARNING: Servos can draw a considerable amount of current. Make sure your system can handle this or you may risk your hardware! + / + #define FEATURE_SERVO 0 + #define SERVO0_PIN 11 + #define SERVO1_PIN -1 + #define SERVO2_PIN -1 + #define SERVO3_PIN -1 + #define FEATURE_WATCHDOG 1 + + // #################### Z-Probing ##################### + + #define FEATURE_Z_PROBE 1 + #define Z_PROBE_BED_DISTANCE 10 + #define Z_PROBE_PIN ORIG_Z_MIN_PIN + #define Z_PROBE_PULLUP 1 + #define Z_PROBE_ON_HIGH 1 + #define Z_PROBE_X_OFFSET 0 + #define Z_PROBE_Y_OFFSET 0 + #define Z_PROBE_WAIT_BEFORE_TEST 0 + #define Z_PROBE_SPEED 2 + #define Z_PROBE_XY_SPEED 150 + #define Z_PROBE_SWITCHING_DISTANCE 1 + #define Z_PROBE_REPETITIONS 1 + #define Z_PROBE_HEIGHT 40 + #define Z_PROBE_START_SCRIPT "" + #define Z_PROBE_FINISHED_SCRIPT "" + #define FEATURE_AUTOLEVEL 1 + #define Z_PROBE_X1 20 + #define Z_PROBE_Y1 20 + #define Z_PROBE_X2 160 + #define Z_PROBE_Y2 20 + #define Z_PROBE_X3 100 + #define Z_PROBE_Y3 160 + #define FEATURE_AXISCOMP 0 + #define AXISCOMP_TANXY 0 + #define AXISCOMP_TANYZ 0 + #define AXISCOMP_TANXZ 0 + + #ifndef SDSUPPORT // Some boards have sd support on board. These define the values already in pins.h + #define SDSUPPORT 1 + #define SDCARDDETECT SDCARDDETECT + #define SDCARDDETECTINVERTED 0 + #endif + #define SD_EXTENDED_DIR 1 /* Show extended directory including file length. Don't use this with Pronterface! / + #define ARC_SUPPORT 1 + #define FEATURE_MEMORY_POSITION 1 + #define FEATURE_CHECKSUM_FORCED 0 + #define FEATURE_FAN_CONTROL 1 + #define FEATURE_CONTROLLER 2 + #define UI_LANGUAGE 0 + #define UI_PRINTER_NAME "ATOM 3D" + #define UI_PRINTER_COMPANY "Alt Design" + #define UI_PAGES_DURATION 4000 + #define UI_ANIMATION 0 + #define UI_SPEEDDEPENDENT_POSITIONING 0 + #define UI_DISABLE_AUTO_PAGESWITCH 1 + #define UI_AUTORETURN_TO_MENU_AFTER 30000 + #define FEATURE_UI_KEYS 0 + #define UI_ENCODER_SPEED 1 + #define UI_KEY_BOUNCETIME 10 + #define UI_KEY_FIRST_REPEAT 500 + #define UI_KEY_REDUCE_REPEAT 50 + #define UI_KEY_MIN_REPEAT 50 + #define FEATURE_BEEPER 0 + #define CASE_LIGHTS_PIN -1 + #define CASE_LIGHT_DEFAULT_ON 1 + #define UI_START_SCREEN_DELAY 1000 + /* + Beeper sound definitions for short beeps during key actions + and longer beeps for important actions. + Parameter is delay in microseconds and the secons is the number of repetitions. + Values must be in range 1..255 + / + #define BEEPER_SHORT_SEQUENCE 2,2 + #define BEEPER_LONG_SEQUENCE 8,8 + #define UI_SET_PRESET_HEATED_BED_TEMP_PLA 60 + #define UI_SET_PRESET_EXTRUDER_TEMP_PLA 190 + #define UI_SET_PRESET_HEATED_BED_TEMP_ABS 110 + #define UI_SET_PRESET_EXTRUDER_TEMP_ABS 240 + #define UI_SET_MIN_HEATED_BED_TEMP 30 + #define UI_SET_MAX_HEATED_BED_TEMP 120 + #define UI_SET_MIN_EXTRUDER_TEMP 170 + #define UI_SET_MAX_EXTRUDER_TEMP 260 + #define UI_SET_EXTRUDER_FEEDRATE 2 + #define UI_SET_EXTRUDER_RETRACT_DISTANCE 3 + + #endif + + / Below you will find the configuration string, that created this Configuration.h + + ========== Start configuration string ========== + { + "editMode": 2, + "processor": 0, + "baudrate": 250000, + "xStepsPerMM": 80, + "yStepsPerMM": 80, + "zStepsPerMM": 80, + "xInvert": "1", + "xInvertEnable": 0, + "eepromMode": 1, + "yInvert": "1", + "yInvertEnable": 0, + "zInvert": "1", + "zInvertEnable": 0, + "extruder": [ + { + "id": 0, + "heatManager": 1, + "pidDriveMin": 40, + "pidDriveMax": 210, + "pidMax": 210, + "sensorType": 8, + "sensorPin": "TEMP_0_PIN", + "heaterPin": "HEATER_0_PIN", + "maxFeedrate": 300, + "startFeedrate": 20, + "invert": "0", + "invertEnable": "0", + "acceleration": 3000, + "watchPeriod": 1, + "pidP": 20.74, + "pidI": 3.19, + "pidD": 33.68, + "advanceK": 0, + "advanceL": 0, + "waitRetractTemp": 150, + "waitRetractUnits": 0, + "waitRetract": 0, + "stepsPerMM": 100, + "coolerPin": -1, + "coolerSpeed": 255, + "selectCommands": "", + "deselectCommands": "", + "xOffset": 0, + "yOffset": 0, + "xOffsetSteps": 0, + "yOffsetSteps": 0, + "stepper": { + "name": "Extruder 0", + "step": "ORIG_E0_STEP_PIN", + "dir": "ORIG_E0_DIR_PIN", + "enable": "E0_ENABLE_PIN" + }, + "advanceBacklashSteps": 0, + "decoupleTestPeriod": 12 + } + ], + "uiLanguage": 0, + "uiController": 0, + "xMinEndstop": 0, + "yMinEndstop": 0, + "zMinEndstop": 1, + "xMaxEndstop": 2, + "yMaxEndstop": 2, + "zMaxEndstop": 2, + "motherboard": 33, + "driveSystem": 3, + "xMaxSpeed": 300, + "xHomingSpeed": 80, + "xTravelAcceleration": 4500, + "xPrintAcceleration": 3000, + "yMaxSpeed": 300, + "yHomingSpeed": 80, + "yTravelAcceleration": 4500, + "yPrintAcceleration": 3000, + "zMaxSpeed": 300, + "zHomingSpeed": 80, + "zTravelAcceleration": 4500, + "zPrintAcceleration": 3000, + "xMotor": { + "name": "X motor", + "step": "ORIG_X_STEP_PIN", + "dir": "ORIG_X_DIR_PIN", + "enable": "ORIG_X_ENABLE_PIN" + }, + "yMotor": { + "name": "Y motor", + "step": "ORIG_Y_STEP_PIN", + "dir": "ORIG_Y_DIR_PIN", + "enable": "ORIG_Y_ENABLE_PIN" + }, + "zMotor": { + "name": "Z motor", + "step": "ORIG_Z_STEP_PIN", + "dir": "ORIG_Z_DIR_PIN", + "enable": "ORIG_Z_ENABLE_PIN" + }, + "enableBacklash": "0", + "backlashX": 0, + "backlashY": 0, + "backlashZ": 0, + "stepperInactiveTime": 360, + "maxInactiveTime": 0, + "xMinPos": 0, + "yMinPos": 0, + "zMinPos": 0, + "xLength": 200, + "yLength": 200, + "zLength": 350, + "alwaysCheckEndstops": "0", + "disableX": "0", + "disableY": "0", + "disableZ": "0", + "disableE": "0", + "xHomeDir": "-1", + "yHomeDir": "-1", + "zHomeDir": 1, + "xEndstopBack": 0, + "yEndstopBack": 0, + "zEndstopBack": 0, + "deltaSegmentsPerSecondPrint": 180, + "deltaSegmentsPerSecondTravel": 70, + "deltaDiagonalRod": 228.82, + "deltaHorizontalRadius": 105.31, + "deltaAlphaA": 210, + "deltaAlphaB": 330, + "deltaAlphaC": 90, + "deltaDiagonalCorrA": 0, + "deltaDiagonalCorrB": 0, + "deltaDiagonalCorrC": 0, + "deltaMaxRadius": 105, + "deltaFloorSafetyMarginMM": 15, + "deltaRadiusCorrA": 0, + "deltaRadiusCorrB": 0, + "deltaRadiusCorrC": 0, + "deltaXOffsetSteps": 0, + "deltaYOffsetSteps": 0, + "deltaZOffsetSteps": 0, + "deltaSegmentsPerLine": 24, + "stepperHighDelay": 0, + "directionDelay": 0, + "stepDoublerFrequency": 12000, + "allowQuadstepping": "1", + "doubleStepDelay": 1, + "maxHalfstepInterval": 1999, + "maxJerk": 20, + "maxZJerk": 20, + "moveCacheSize": 16, + "moveCacheLow": 10, + "lowTicksPerMove": 250000, + "enablePowerOnStartup": "1", + "echoOnExecute": "1", + "sendWaits": "1", + "ackWithLineNumber": "1", + "killMethod": 1, + "useAdvance": "0", + "useQuadraticAdvance": "0", + "powerInverting": 0, + "mirrorX": "0", + "mirrorXMotor": { + "name": "Extruder 1", + "step": "ORIG_E1_STEP_PIN", + "dir": "ORIG_E1_DIR_PIN", + "enable": "ORIG_E1_ENABLE_PIN" + }, + "mirrorY": 0, + "mirrorYMotor": { + "name": "Extruder 1", + "step": "ORIG_E1_STEP_PIN", + "dir": "ORIG_E1_DIR_PIN", + "enable": "ORIG_E1_ENABLE_PIN" + }, + "mirrorZ": 0, + "mirrorZMotor": { + "name": "Extruder 1", + "step": "ORIG_E1_STEP_PIN", + "dir": "ORIG_E1_DIR_PIN", + "enable": "ORIG_E1_ENABLE_PIN" + }, + "dittoPrinting": "0", + "featureServos": "0", + "servo0Pin": 11, + "servo1Pin": -1, + "servo2Pin": -1, + "servo3Pin": -1, + "featureWatchdog": "1", + "hasHeatedBed": "0", + "enableZProbing": "1", + "extrudeMaxLength": 160, + "homeOrder": "HOME_ORDER_ZXY", + "featureController": 2, + "uiPrinterName": "ATOM 3D", + "uiPrinterCompany": "Alt Design", + "uiPagesDuration": 4000, + "uiAnimation": "0", + "uiDisablePageswitch": "1", + "uiAutoReturnAfter": 30000, + "featureKeys": "0", + "uiEncoderSpeed": 1, + "uiKeyBouncetime": 10, + "uiKeyFirstRepeat": 500, + "uiKeyReduceRepeat": 50, + "uiKeyMinRepeat": 50, + "featureBeeper": "0", + "uiPresetBedTempPLA": 60, + "uiPresetBedABS": 110, + "uiPresetExtruderPLA": 190, + "uiPresetExtruderABS": 240, + "uiMinHeatedBed": 30, + "uiMaxHeatedBed": 120, + "uiMinEtxruderTemp": 170, + "uiMaxExtruderTemp": 260, + "uiExtruderFeedrate": 2, + "uiExtruderRetractDistance": 3, + "uiSpeeddependentPositioning": "0", + "maxBedTemperature": 120, + "bedSensorType": 1, + "bedSensorPin": "TEMP_1_PIN", + "bedHeaterPin": "HEATER_1_PIN", + "bedHeatManager": 0, + "bedUpdateInterval": 5000, + "bedPidDriveMin": 80, + "bedPidDriveMax": 255, + "bedPidP": 196, + "bedPidI": 33, + "bedPidD": 290, + "bedPidMax": 255, + "bedDecoupleTestPeriod": 300, + "caseLightPin": -1, + "caseLightDefaultOn": "1", + "bedSkipIfWithin": 3, + "gen1T0": 25, + "gen1R0": 100000, + "gen1Beta": 4036, + "gen1MinTemp": -20, + "gen1MaxTemp": 300, + "gen1R1": 0, + "gen1R2": 4700, + "gen2T0": 25, + "gen2R0": 100000, + "gen2Beta": 4036, + "gen2MinTemp": -20, + "gen2MaxTemp": 300, + "gen2R1": 0, + "gen2R2": 4700, + "gen3T0": 25, + "gen3R0": 100000, + "gen3Beta": 4036, + "gen3MinTemp": -20, + "gen3MaxTemp": 300, + "gen3R1": 0, + "gen3R2": 4700, + "userTable0": { + "r1": 0, + "r2": 4700, + "temps": [ + + ] + }, + "userTable1": { + "r1": 0, + "r2": 4700, + "temps": [ + + ] + }, + "userTable2": { + "r1": 0, + "r2": 4700, + "temps": [ + + ] + }, + "tempHysteresis": 0, + "pidControlRange": 20, + "skipM109Within": 2, + "extruderFanCoolTemp": 50, + "minTemp": 150, + "maxTemp": 275, + "minDefectTemp": -10, + "maxDefectTemp": 290, + "arcSupport": "1", + "featureMemoryPositionWatchdog": "1", + "forceChecksum": "0", + "sdExtendedDir": "1", + "featureFanControl": "1", + "fanPin": "ORIG_FAN_PIN", + "scalePidToMax": 0, + "zProbePin": "ORIG_Z_MIN_PIN", + "zProbeBedDistance": 10, + "zProbePullup": "1", + "zProbeOnHigh": "1", + "zProbeXOffset": 0, + "zProbeYOffset": 0, + "zProbeWaitBeforeTest": "0", + "zProbeSpeed": 2, + "zProbeXYSpeed": 150, + "zProbeHeight": 40, + "zProbeStartScript": "", + "zProbeFinishedScript": "", + "featureAutolevel": "1", + "zProbeX1": 20, + "zProbeY1": 20, + "zProbeX2": 160, + "zProbeY2": 20, + "zProbeX3": 100, + "zProbeY3": 160, + "zProbeSwitchingDistance": 1, + "zProbeRepetitions": 1, + "sdSupport": "1", + "sdCardDetectPin": "SDCARDDETECT", + "sdCardDetectInverted": "0", + "uiStartScreenDelay": 1000, + "xEndstopBackMove": 1, + "yEndstopBackMove": 1, + "zEndstopBackMove": 1, + "xEndstopRetestFactor": 5, + "yEndstopRetestFactor": 5, + "zEndstopRetestFactor": 5, + "xMinPin": -1, + "yMinPin": -1, + "zMinPin": "ORIG_Z_MIN_PIN", + "xMaxPin": "ORIG_X_MAX_PIN", + "yMaxPin": "ORIG_Y_MAX_PIN", + "zMaxPin": "ORIG_Z_MAX_PIN", + "deltaHomeOnPower": "0", + "fanBoardPin": -1, + "heaterPWMSpeed": 0, + "featureBabystepping": "1", + "babystepMultiplicator": 1, + "pdmForHeater": "1", + "pdmForCooler": "1", + "psOn": "ORIG_PS_ON_PIN", + "mixingExtruder": "0", + "decouplingTestMaxHoldVariance": 20, + "decouplingTestMinTempRise": 1, + "featureAxisComp": "0", + "axisCompTanXY": 0, + "axisCompTanXZ": 0, + "axisCompTanYZ": 0, + "retractOnPause": 2, + "pauseStartCommands": "", + "pauseEndCommands": "", + "hasMAX6675": false, + "hasMAX31855": false, + "hasGeneric1": false, + "hasGeneric2": false, + "hasGeneric3": false, + "hasUser0": false, + "hasUser1": false, + "hasUser2": false, + "numExtruder": 1, + "version": 92 + } + ========== End configuration string ========== + */