Zebra Plate by PRINTinZ

產品描述

Zebra Plate 厚度: 4.5mm +/-0.4mm

長寬誤差: +/-1mm

熱床: 床溫最高110°C  (ZP床板表面約70°C)

See the Support page for much more information about the Zebra Plate

材料相容性

ATOM使用注意

  1. G29不要加熱狀態下跑
  2. 注意噴嘴不要停止在ZP上噴頭還是熱的
  3. 下面一定要有玻璃或其他材質硬板,要凹到中央下方微突起朝下,周圍用夾子夾才會平整(請細看下面的影片解說)
  4. 詳讀本說明

安裝

*

https://www.youtube.com/watch?v=7wiuBIGDFGw

水平調整與噴嘴間距設定

http://cdn2.bigcommerce.com/n-d57o0b/qutbkhxr/product_images/uploaded_images/backoff-image.png?t=1436141019

調整附著力

PLA 和 PLA 衍生線材

試著就直接印不用熱床.如果遇到很難印的物件,在邊角翹得很厲害, 這時就可以考慮開熱床.但建議不要熱到ZP表面超過40°C. 因為怕附著力過度了.

ABS

ZP 可以熱床開到110°C 來印ABS, ZP上表面溫度 70-80°C , 但PRINTinZ高度建議表面溫度在50°C 開始, 看需要而提高溫度. 有機殼封閉保溫也可有效防翹, 另外並不建議ABS大型物件用100%填充, 翹曲的力量可能會大到彎曲ZP甚至破壞底板, 請量力而為.

其他線材

PETG 和木料使用類似PLA, 金屬線材通常也是.

移除物件

印出來的物件形狀不同, 移除的方法也就不盡相同. 有些物件, 輕輕折一下ZP可能就脫落了.但有些物件,尤其是小或薄的, 你就可能要使用銳利的油漆刮刀, 切麵刀(別用刮鬍刀) 記得戴厚手套保護你的手. 盡量保持刀具跟ZP平行,才不會刮壞板子(ZP沒有玻璃耐刮), 刀面寬度4cm以上的很有幫助.

*

https://www.youtube.com/watch?feature=player_embedded&v=R1Gwj2J_3aQ

*

https://www.youtube.com/watch?feature=player_embedded&v=KFvT-sbsYCA

*

https://www.youtube.com/watch?feature=player_embedded&v=mqf_V7m0kv4

*

https://www.youtube.com/watch?v=ECcasNza1Oo

熱床

ZP是由幾層不同材料組成. 這些材料是低膨脹係數的, 但加熱後各層會稍微延展(水平為主). 這樣會造成些碗型, 因為各層材料的膨脹係數不同, 碗型的嚴重程度也跟燕尾夾的力道可以抗衡多少有關. 這是為什麼不建議用高溫印大型高填充的ABS, 還有熱床溫度不平均的也會造成問題.

平台碗型

列印或彎折ZP後殘留的任何碗型, 可以透過反折平台來減少. 在平坦的表面上旋轉ZP, 可以檢驗是否還有碗型跟定位位置. 永遠將平台"圓頂面朝下"安裝, 這樣燕尾夾可以把輕微殘留的碗型拉平.

使用溶劑

建議只使用異丙醇(IPA), 可移除灰塵跟油脂和協助附著力. 列印前確保已經完全乾燥. 不要使用丙酮(Acetone)或去光水, 實驗證明會損傷表面, 尤其是接觸超過數分鐘以上.卡住的物質可以用刮除了,然後小心磨平

改裝

切割建議使用桌鋸配切磁磚的鑽石刀, 其次是帶鋸機, 線鋸也許可以. 但千萬不要用雷射切割. [這批團購圓盤是CNC水刀加工]

鑽孔使用一般的麻花鑽頭即可,記得出孔處要良好的支撐.

邊緣應該要磨過減少銳利邊角

自行加工過不可退貨. 但PRINTinZ是接受客製特定尺寸形狀的.

Machine specific information

Note: This list is not all inclusive. Your printer may need a spacer or end stop adjustment.

PRINTER COMMENTS
Makerbot Replicator 2 The Zebra? plate has cut-outs to clear the printer bed clips. We recommend printing your own clips. Search Thingiverse for "Ninja Clips". Not every plate is exactly the same thickness so you may need to adjust the clips to suit your plate. There is also a Z axis stop you need to print to compensate for the plate thickness. Please see this page for details.
Ultimaker 2 The Zebra? plate will replace the glass. It fits under the machine's clips. Add more clips if you like.
Printrbot Simple Metal Included is a layer of copper (on both sides) to enable the use of the inductive proximity sensor found on the Printrbot Simple Metal for auto leveling. Mount this Zebra? plate to your machine by using small binder clips (or printed clips of your own design) to fasten it on top of your build platform.  Be sure they won't hit the machine frame. Please note that the thickness of the outer layer may vary from one side of the plate to the other. Double check your calibration when flipping the plate over.
Delta machines Round Zebra? plates can be clipped to your delta style machine just like other beds. Even bed heating is important with the round plates.
BQ Witbox The witbox needs a Z-axis spacer installed to offset for the Zebra? plate thickness.
FlashForge There is a printable shim for the Z-axis here.